The young lad has his P's now and this was too much time and $ to get going for a part time dishwasher and school student ... so I am going to drive it and he is into a MK3 Vento. He is smart enough to know this will be around to drive also.
The consequences for the car are that this will now remain original running gear and a member of the high rollers club (How's that logo going warb ) instead of being slammed etc etc
Andrew (pmgbus) is doing the metal work as we speak - hence post in wanted section for headboard/separation panel.
It is going to be a down to earth (but still a high roller - irony), get dirty with me ute for daily hack work. Metal wise it needs front cross brace, outriggers and jacking poiints front and rear, inner sill drivers side, floor drivers side.
The passenger B pillar is bent badly and the headboard is stuffed.
Cheers
Nick
Attachments
singlecab wed 002.jpg (65.73 KiB) Viewed 7832 times
ute update 225.jpg (69.11 KiB) Viewed 7832 times
ute update 201.jpg (69.82 KiB) Viewed 7835 times
singlecab wed 001.jpg (55.23 KiB) Viewed 7835 times
niks split singlecab 001.jpg (35.07 KiB) Viewed 7835 times
Last edited by Kombi Trip on Sat Mar 17, 2012 4:09 pm, edited 5 times in total.
Imagine what you would do if you knew you couldn't fail.
Andrew continues to 'live the dream' getting this thing solid for me
Some clever stuff has happened. Feel free to pump up your tyres Andrew.
the marking on the gearbox has me stumped - stamped 'MOD CASE' and is a Limited Slip Diff. Will post more pics if I can get off my phone.
Attachments
niks split singlecab 002.jpg (29.22 KiB) Viewed 7645 times
gearbox 003.jpg (37 KiB) Viewed 7645 times
Imagine what you would do if you knew you couldn't fail.
yes as per usual, get it done is the aim.
yes you can replace the inner sill without damaging the outer sill and paint, yes you can replace the tophat front outriggers and front centre crossmember without cutting the floor,
yes as per usual there is more rust than we would have liked, but it is a ute and you never know what you are going to find until you cut it open.....
Overall i would have to say it is one of the better high top "projects" i have seen/worked on with minimal of the "usual high top" rust ie under tray box section. upper roof skin....
anyway, back to living the dream .... should be out and registered in 3/4 weeks
the patches in the ute tray - an old 'repair' that was only going to let water into all of the new metal below - so the initial plan to leave has changed. Andrew is a machine once he picks up those orange handled scissors
The round hole at the back passenger side of the tray was for the air cleaner intake a pipe up thtough the tray floor - but was also a major water catcher into the after market truck air filter stored below.
Attachments
singlecab 13 may 002.jpg (67.88 KiB) Viewed 7431 times
singlecab 13 may 003.jpg (67.4 KiB) Viewed 7431 times
singlecab 13 may 004.jpg (85.17 KiB) Viewed 7431 times
singlecab 13 may 005.jpg (38.41 KiB) Viewed 7431 times
ute update 209.jpg (74.49 KiB) Viewed 7431 times
Imagine what you would do if you knew you couldn't fail.
previous patches had been brazed in so new patches had to be too.
The underneath (floor chassis etc) and the tray are getting a decent brush coat of KILLRUST paint. The tray is way way too white and cannot be approached without sunglasses - so I will have to change that.
Headboard and a few other bits will be blown in to match the paint painted over the top of the OG white on most of the rest of the van.
Gearbox is back in now too.
Attachments
may10 054.jpg (71.19 KiB) Viewed 7320 times
june 001.jpg (67.83 KiB) Viewed 7320 times
june 010.jpg (47.95 KiB) Viewed 7320 times
may10 016.jpg (38.37 KiB) Viewed 7320 times
june 004.jpg (41.76 KiB) Viewed 7320 times
Imagine what you would do if you knew you couldn't fail.
seat covers will be dark grey so have taken a piece to Bunnings to colour match to paint the interior cards - roof x 3, 2 x door cards, 2 x kick panels. Door card repros needed 10mm of short end and planing on the front edge - -PIA. Hopefully I have the holes correct.
Preview of wheels and sound.
Kill rust is my 3rd biggest supplier - after pmgbus and cip1 All 3 have been great.
Attachments
june 035.jpg (67.9 KiB) Viewed 7093 times
june 006.jpg (34.05 KiB) Viewed 7094 times
june 037.jpg (54.13 KiB) Viewed 7094 times
june 023.jpg (85.56 KiB) Viewed 7195 times
june 031.jpg (61.25 KiB) Viewed 7195 times
Last edited by Kombi Trip on Wed Jul 27, 2011 6:34 pm, edited 3 times in total.
Imagine what you would do if you knew you couldn't fail.
) instead of being slammed etc etc 
Feel free to pump up your tyres Andrew. 
All 3 have been great.