58 11 window " The Cubby Hut "

ogrule · Post by **ogrule** » Sun May 14, 2017 1:17 pm

Massive job - enjoying your build

vanell · Post by **vanell** » Sun May 14, 2017 2:33 pm

Thanks for the comments, been laid up with the flu, can't seem to shake it, might be a while to a update, been modifying my rottisorie to be a jig to get the front axle to rear axle spacings right, Pat here in Adelaide has made a jig to locate the front on and get the door gaps, I still think this is a easy job compared to fixing a crashed bus, all the main floor section is in great condition and I'm not fixing that much rust, seems easy to me an taken me a lot less time than fixing that Darwin bus roof, Ian

Wassa · Post by **Wassa** » Sun May 14, 2017 7:02 pm

So right mate, my dad being a panel beater hated rust big time, sooner do a bent up smash anytime .....

vanell · Post by **vanell** » Fri May 19, 2017 12:27 pm

So while I havnt been feeling that good with the flu ive decided to start the straight axle conversion, I start out by measuring the long housing with the bearing in, because the short housing is different where the bearing goes.

: IMG_1920.JPG (36.06 KiB) Viewed 3081 times

you can see the bearing sticks out more on the short housing, about 3 mm. Then you cut the short housings as close to the cone as possible, and cut the long housings near the brake line bracket about 125mm will do. I trim the housings in my Brobo for a nice square cut, and the I trim down the cone part in the lathe till I get the right lenght,

: straight axle.JPG (40.08 KiB) Viewed 3081 times

the end result is the part that bolts to the spring plate is now 30mm closer to the brake drum, and thats because splitty housings are 30mm each side wider than a beetle.

: IMG_1923.JPG (35.88 KiB) Viewed 3081 times

put the metal 6bolt plate on before you weld, the weld will be covered by the seals, make sure you use the short housing bearing covers because of the difference in the housings, I have type 3 brake drums for these which I turn upside down so the hand brake cable is at the top, and use splitty rear brake cylinders coz the bleeder is above the inlet pipe, Regards Ian

rabidkombi · Post by **rabidkombi** » Sat May 20, 2017 4:20 pm

Awesome info,thank you

vanell · Post by **vanell** » Sun May 21, 2017 7:20 pm

After a lot of cutting, trimming, drilling out spot welds, I finally got to trial fit the front floor section, its only got a couple of scews in it but it seems to fit great, will put the doglegs on properly tommorrow and trial fit the doors.

: IMG_1926.JPG (35.86 KiB) Viewed 3040 times

: IMG_1928.JPG (32.94 KiB) Viewed 3040 times

: IMG_1927.JPG (37.4 KiB) Viewed 3040 times

: IMG_1925.JPG (37.41 KiB) Viewed 3040 times

Ged · Post by **Ged** » Mon May 22, 2017 6:38 pm

Wow such great work.
There's not that much holding a bus together is there.

bulliboy · Post by **bulliboy** » Mon May 22, 2017 7:33 pm

Ged wrote:Wow such great work.
There's not that much holding a bus together is there.

not that one!
In the age of facebook great to see forumbased quality sharing. keep it up thanks.

m

StevieVW · Post by **StevieVW** » Mon May 22, 2017 8:02 pm

Nice work, i should get into mine.

Social media getts forgotten, forum resto's live on alot longer ive noticed.

Leroy · Post by **Leroy** » Tue May 23, 2017 7:26 pm

Absolutely love this build! Thanks for the quality posts. This is what keeps a forum alive.

vanell · Post by **vanell** » Tue May 30, 2017 7:22 pm

Big thanks to Pat from Adelaide for the lend of his jig, it has made the job easier to get straight

: IMG_1952.JPG (41.22 KiB) Viewed 2950 times

: IMG_1946.JPG (44.35 KiB) Viewed 2950 times

vanell · Post by **vanell** » Tue May 30, 2017 7:28 pm

The test today was to see if a door fits, I used the one from my darwin bus, and its just screwed together with a few tacks but it has exceeded my expectations, the door gap first fit was just amazing, all because of Pats jig.

: IMG_1956.JPG (32.22 KiB) Viewed 2950 times

: IMG_1955.JPG (23.98 KiB) Viewed 2950 times

: IMG_1954.JPG (30.55 KiB) Viewed 2950 times

vanell · Post by **vanell** » Tue May 30, 2017 7:35 pm

Also test fitted the safari windows, little bit of massage but they seem to fit good

: IMG_1948.JPG (37.06 KiB) Viewed 2949 times

Today seems like I have achieved the result that I was going for, its all nice to be confident and optomistic but to get over this hurdle is just great, thanks to all the people who have supplied all the parts to weld this back together. Ian

braddick · Post by **braddick** » Tue May 30, 2017 7:50 pm

Massive hats off to u Ian that is a great effort to bring this bus back from the dead
The cubby found the right owner in u

kavman · Post by **kavman** » Wed May 31, 2017 2:17 pm

wonder how many years the poor thing was missing a face, looking better with each post, keep up the good work

58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "

Re: 58 11 window " The Cubby Hut "