'63 11 window
Moderators: warb, Rawdyn, Leroy, byronbus, Tonz Magonz, dmb
-
- DSKer
- Posts: 957
- Joined: Fri May 17, 2013 1:07 pm
Re: '63 11 window
How's progress bud
I bet u wishing u could squeeze a fire in that she'd to stay warm this last weekend
Might have to squeeze another visit in next time I'm in town
I bet u wishing u could squeeze a fire in that she'd to stay warm this last weekend
Might have to squeeze another visit in next time I'm in town
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
Re: '63 11 window
Long side vertical supports repaired and inner sill clamped in for trial fit. Also front section of wheel arch cut out and repair section clamped in place...
Front right side outrigger prepared and welded in...
The right rear outrigger prep'd and welded in...
Front of wheel arch welded in and ground back. Also inner sill welded in place. Forgot to take more pics of this...
Front right side outrigger prepared and welded in...
The right rear outrigger prep'd and welded in...
Front of wheel arch welded in and ground back. Also inner sill welded in place. Forgot to take more pics of this...
- warb
- Mod
- Posts: 7515
- Joined: Mon May 16, 2005 5:15 pm
- Location: Penrith, Nsw, Australia
- Contact:
Re: '63 11 window
mint
- D-Train
- DSKer
- Posts: 3505
- Joined: Mon Nov 28, 2005 3:03 pm
- Location: coffs harbour
Re: '63 11 window
Nice work!!!
- splitthis
- DSKer
- Posts: 1607
- Joined: Wed Nov 28, 2007 8:47 pm
- Location: Adelaide
- Contact:
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
Re: '63 11 window
Now on to the B pillar. Got the rusted out section cut out and cut this KF panel to suit. Very nice fit.
Welded in after a quick alignment check with the long side..
Welds ground back and ready to repair the bulkhead edge...
Bulkhead repair. Still more grinding to be done (welds on outrigger etc.) but getting there...
Welded in after a quick alignment check with the long side..
Welds ground back and ready to repair the bulkhead edge...
Bulkhead repair. Still more grinding to be done (welds on outrigger etc.) but getting there...
-
- DSKer
- Posts: 957
- Joined: Fri May 17, 2013 1:07 pm
Re: '63 11 window
Looking good bud
Was heading to natti for footy this week until dickhead Dan stepped up and lock the state down again and was going pop around for another look
Was heading to natti for footy this week until dickhead Dan stepped up and lock the state down again and was going pop around for another look
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
Re: '63 11 window
Painted behind the rear corner in areas which will be difficult to spray once it is install. Weld through primer inside the pillar for protection.
With the long panel trial fitted and clamped on, it was time to weld the rear corner on. The rear edge of the long panel was clamped to ensure correct fitment...
OG taillight section was used to trace on before cutting the new hole. Used all of the dimensions that I took before cutting off the rear corner.
Welds ground back and ready for a quick spray of primer...
With the long panel trial fitted and clamped on, it was time to weld the rear corner on. The rear edge of the long panel was clamped to ensure correct fitment...
OG taillight section was used to trace on before cutting the new hole. Used all of the dimensions that I took before cutting off the rear corner.
Welds ground back and ready for a quick spray of primer...
-
- DSKer
- Posts: 1626
- Joined: Sat Jul 15, 2006 3:58 pm
Re: '63 11 window
Going good Rusty, gotta love a Lockdown to get things done, and did Dan just give you another week of Lockdown?
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
Re: '63 11 window
Side window repairs, long side inner support repaired (no pics of it welded in) and right side jacking points...
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC
Re: '63 11 window
Engine hatch trial fit and setting the location...
Stripping paint and getting some primer on the right side inner...
Fixing up a hole which was hacked above the fuel tank...
Finishing off the details on the ribs to make them look the part...
Still some finishing to do but basically have it buttoned up, just the hinge carriers to dress up and weld on...
Damaged section cut out and repaired...
Stripping paint and getting some primer on the right side inner...
Fixing up a hole which was hacked above the fuel tank...
Finishing off the details on the ribs to make them look the part...
Still some finishing to do but basically have it buttoned up, just the hinge carriers to dress up and weld on...
Damaged section cut out and repaired...
- Cam Biscuit
- DSKer
- Posts: 1523
- Joined: Sun Feb 26, 2012 4:56 pm
- Location: Radelaide
Re: '63 11 window
Good progress BDR !
- D-Train
- DSKer
- Posts: 3505
- Joined: Mon Nov 28, 2005 3:03 pm
- Location: coffs harbour
Re: '63 11 window
Hatch job looks good. They should of had them from day 1! Did u reinforce it anywhere else?
- MID WEST DUBBER
- DSKer
- Posts: 1329
- Joined: Fri Jan 06, 2012 4:49 pm
- Location: Near Horsham, VIC