61 split ute

[Griffin]

I think I have to get one of these diesel heaters, how much fuel does it use Ian?

[vanell]

Very little, I only made a small tank for the diesel about 2 litres, had it running about 6 hours so far hasn’t run out, I’ll let it run out so I can see how much it uses
I think Warb would have a better idea of how much it would use
Picture of the tank I made

IMG_7940.jpeg (99.45 KiB) Viewed 12190 times

[braddick]

Very little, I only made a small tank for the diesel about 2 litres, had it running about 6 hours so far hasn’t run out, I’ll let it run out so I can see how much it uses
I think Warb would have a better idea of how much it would use
Picture of the tank I made IMG_7940.jpeg

I’m hoping there another tank the same size on the other side as well mate
Hope u get the joke
Cheers bud

[warb]

usage, easy as, uses three fifths of fuck all...ha.. the pulse pump moves .02ml every time it clicks, and the frequencey of the pump is set at the contriller (Hz) .. so on the controler if you set it to 3.0hz per second, so 3x.02 is .06ml per second, or 3.6ml per minute, or 216ml per hour - however in that cab I reckon youll be running it at 2Hz max?

bit more math, lets say you play $2 per litre for the diesel, that 2l tank should run for just over 9 hours at 3Hz.. for $4...

pretty sure I worked that right...

[morts]

Very little, I only made a small tank for the diesel about 2 litres, had it running about 6 hours so far hasn’t run out, I’ll let it run out so I can see how much it uses
I think Warb would have a better idea of how much it would use
Picture of the tank I made IMG_7940.jpeg

I’m hoping there another tank the same size on the other side as well mate
Hope u get the joke
Cheers bud

[vanell]

Well I guess I was a bit cocky on how good the diesel heaters are, on the way back it started to smoke and stopped working, got to Champs workshop and checked a few things out but couldn’t get it to work

Resized_20230623_103658_7391.jpeg (346.22 KiB) Viewed 12024 times

Got home and bought a new one $133 on EBay, fitted it today, 2kw version this time, and it’s working a treat
Still think it’s a great idea instead of heater boxes

[warb]

that fucker is flooded man. blow the shit out of it, check the glowplug is above the fuel inlet.. run it hot and hard, add kero. 50/50... chuck in a new glow plug first too..

[spl65t]

Geez, lucky the emergency exit is just on the other side of the bus

[morts]

Reminds me of a smoke machine from my disco days...

[Griffin]

Got home and bought a new one $133 on EBay, fitted it today, 2kw version this time, and it’s working a treat
Still think it’s a great idea instead of heater boxes

Ian - yopu got a link to the $133 version please? Have to fit one before Volksfest, Old Bar and ReVolks

[vanell]

Not good at the link thing, but I did take a picture of it, the item id is on there

IMG_7982.png (86.62 KiB) Viewed 11983 times

[spl65t]

Got home and bought a new one $133 on EBay, fitted it today, 2kw version this time, and it’s working a treat
Still think it’s a great idea instead of heater boxes

Ian - yopu got a link to the $133 version please? Have to fit one before Volksfest, Old Bar and ReVolks

The $133 version in the picture with Ian above looks a tad smoky - Cheek & Chong Style.
Perhaps go for the $266 model

Linz

[vanell]

The $133 version came with instructions, the first one just had a picture. And I can see what I did wrong with the first one, the new instructions say you need to run it flat out some times to get rid of the junk, I see Warb says to run it flat out as well, I always had it on the lowest setting, and as Warb said I flooded it, I will clean up the first one and get it going again, might make a good shed heater

[Oldfart]

Tray is on, taking it out to Coopers next week to use his spray booth 8D76510C-1C26-4F68-8FE8-CC40180EC352.jpeg2B5795C9-685C-403C-AB7F-BAF1B4057682.jpeg

How did you put the bed on, welded? I see folks are using body adhesive a lot now with panels, in the olden days everything was just welded. Seems you could get a pretty good hold with adhesive on the cross members and mebe just spot around the outside? I have a bed to put on in a couple of months, been loooong time since I've done any panel work and things have changed a bit.

[vanell]

Yep just glued it on, rolled the lip and called it done. And if you ask me what I used just sikaflex, they have a bonding one, got mine from Bunnings