55 microbus
Moderators: warb, Rawdyn, Leroy, byronbus, Tonz Magonz, dmb
-
Cheeseboard
- DSKer
- Posts: 343
- Joined: Fri Sep 10, 2021 6:01 pm
- Location: Victoria
Re: 55 microbus
Good to see the mojo has returned.
Ideas man
Minister for Finance
Scared of wife finding out what I’ve spent
Minister for Finance
Scared of wife finding out what I’ve spent
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Well its about time for another update
Have been chipping away in the evenings after work and when I can on the weekends
Been trying to get the passenger side rear floor and sill done. Not quite done and keep finding little bits to do before I can do the main stuff. Fabbing the bottom of the B and C posts and sill strengthener.
Wasn’t sure what to do about the hole in the tophat for the shift rod, as no tube being a 55. In the end the section from the original cleaned up and put it in the middle of the new
Have been chipping away in the evenings after work and when I can on the weekends
Been trying to get the passenger side rear floor and sill done. Not quite done and keep finding little bits to do before I can do the main stuff. Fabbing the bottom of the B and C posts and sill strengthener.
Wasn’t sure what to do about the hole in the tophat for the shift rod, as no tube being a 55. In the end the section from the original cleaned up and put it in the middle of the new
- Attachments
-
- IMG_6690.jpeg (196 KiB) Viewed 366 times
-
- IMG_6687.jpeg (227.64 KiB) Viewed 366 times
-
- IMG_6688.jpeg (186.04 KiB) Viewed 366 times
-
- IMG_6689.jpeg (260.13 KiB) Viewed 366 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Remade the bottom of the bulkhead (center section) so now can weld on the top hat, and will complete the sides after B posts are done before the doglegs.
Top hat is now on but didn’t get a pic
Also had to repair a section of a heater cable tube and cut back the clutch tube, this was rusted where it went through the cross member. Will fix that one later
Top hat is now on but didn’t get a pic
Also had to repair a section of a heater cable tube and cut back the clutch tube, this was rusted where it went through the cross member. Will fix that one later
- Attachments
-
- IMG_6691.jpeg (261.85 KiB) Viewed 366 times
-
- IMG_6692.jpeg (194.89 KiB) Viewed 366 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Bottom of C post and then trial fitted the sill, I still had the doors on to check alignment. Doors are now off, all bolts removed and plates taped out
- Attachments
-
- IMG_6695.jpeg (225.12 KiB) Viewed 365 times
-
- IMG_6696.jpeg (122.04 KiB) Viewed 365 times
-
- IMG_6697.jpeg (157.43 KiB) Viewed 365 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Onto the B post bottom
Made up the inner piece and welded in so now the post is held in place to the inner sill. Had a go at making the outer its only about 150mm long, 1st attempt was ok but wasn’t really happy with the curve. Wasn’t very smooth, was trying to talk myself into it but in the end started again.
2nd attempt is going well but not done yet but getting there
Made up the inner piece and welded in so now the post is held in place to the inner sill. Had a go at making the outer its only about 150mm long, 1st attempt was ok but wasn’t really happy with the curve. Wasn’t very smooth, was trying to talk myself into it but in the end started again.
2nd attempt is going well but not done yet but getting there
- Attachments
-
- IMG_6693.jpeg (264.91 KiB) Viewed 362 times
-
- IMG_6700.jpeg (190.74 KiB) Viewed 362 times
-
- IMG_6699.jpeg (167.45 KiB) Viewed 362 times
-
- IMG_6694.jpeg (165 KiB) Viewed 362 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
1958kafer
- DSKer
- Posts: 257
- Joined: Sun Aug 16, 2015 10:35 am
Re: 55 microbus
Looks awesome Dave 
-
braddick
- DSKer
- Posts: 974
- Joined: Fri May 17, 2013 1:07 pm
Re: 55 microbus
Nice work Dave
Great to see some more progress
Great to see some more progress
-
splitthis
- DSKer
- Posts: 1616
- Joined: Wed Nov 28, 2007 8:47 pm
- Location: Adelaide
- Contact:
Re: 55 microbus
Great update, good work mate. Will catch up with you this weekend.
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Finished off the bottom of the inner B post and completed the new outer patch ready to be attached.
Not going to put the outer on until I have fixed a hole on the inside of the post just above the bulkhead, not sure why but someone made a big hole right where the semaphore goes. While I’m at it I will put a mount for a seatbelt in the post. Will be much easier to clear any crap out before the bottom gets sealed up
Not going to put the outer on until I have fixed a hole on the inside of the post just above the bulkhead, not sure why but someone made a big hole right where the semaphore goes. While I’m at it I will put a mount for a seatbelt in the post. Will be much easier to clear any crap out before the bottom gets sealed up
- Attachments
-
- IMG_6735.jpeg (171.43 KiB) Viewed 182 times
-
- IMG_6734.jpeg (175.27 KiB) Viewed 182 times
-
- IMG_6738.jpeg (207.21 KiB) Viewed 182 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
rusty 55
- DSKer
- Posts: 607
- Joined: Wed Nov 28, 2007 8:56 pm
- Location: Adelaide
Re: 55 microbus
Cleaned up and primed
- Attachments
-
- IMG_6736.jpeg (179.28 KiB) Viewed 182 times
-
- IMG_6733.jpeg (169.24 KiB) Viewed 182 times
it’s got nuffin to do wiv yer “vor sprung Durch technic” ya know!
-
splitthis
- DSKer
- Posts: 1616
- Joined: Wed Nov 28, 2007 8:47 pm
- Location: Adelaide
- Contact:
Re: 55 microbus
Got to check this out earlier in the week, coming along nicely. fuck that OG paint is so good.