67 panel RHINO A must for sleeping in a Panel

cozza · Post by **cozza** » Sun Apr 22, 2007 11:47 am

Great work Doc. Very inspiring stuff. You should hold a workshop with some of us and get it done even quicker! Seems you've done this before even tho it's your first bus!

beerdoc · Post by **beerdoc** » Sun Apr 22, 2007 6:41 pm

No Cozza first resto of any kind

Had the Guest stripper at it again
This whole side is down to last primer ready for final sand and then epoxy

This Corner is way worse than expected (tell me something new with bus restos I hear yoiu say) will have to replace everything that engine lid hinges on inside and out

More pics later my camera batteries went flat

Shaven · Post by **Shaven** » Mon Apr 23, 2007 9:17 am

slave labour

dont worry mate its onlt brown flakey stuff... it just falls off

beerdoc · Post by **beerdoc** » Sat Apr 28, 2007 6:28 pm

The fidley bit done

Kombi Trip · Post by **Kombi Trip** » Sun Apr 29, 2007 12:22 am

You have great taste Doc. Splitty panel and 2 stroke era GP bikes in one photo!

1kombilover · Post by **1kombilover** » Sun Apr 29, 2007 12:10 pm

well done doc, keep up the good work, you'll see the end of the tunnel soon,cheers johnnie

rustydcab · Post by **rustydcab** » Sun Apr 29, 2007 5:42 pm

Great to see all the hard work starting to pay off Doc, I'll take Matty up on the Latte offer . What say the s west DSK contingent organise a pako st split fest . If you dont bring a split you have to supply a few garage view photos at least. How about 10.00 am Sunday 27 may . Gloria Jeans. BTW was in g town this week and spotted a slammed primer black beetle with copious bling & robs 2xcab. Is this the KDF capital of vic or what? 10 am . be there.

Shaven · Post by **Shaven** » Sun Apr 29, 2007 6:10 pm

hey john...
sounds good... but ill be bring the bay DC, its to far to push my split. hehe
ill give u both a call as time gets closer... anyone else in mexico coming???
matty

Zimblewinder · Post by **Zimblewinder** » Sun Apr 29, 2007 8:52 pm

If Im not working Itll be a good chance to finally meet all of you. Hope to see you then.

Cheers
Dale

beerdoc · Post by **beerdoc** » Sun May 13, 2007 5:58 pm

Coffee sounds good but it will be at Tarts On Pako which is a couple of blocks north from GJs

Finally finsihed the tailgate/rear door bracket This was completley cut out and used some spare floor created when installed type 3 lid

Just have to weld it up and round we go to drivers side

Shaven · Post by **Shaven** » Sun May 13, 2007 10:48 pm

doc...
thats craftmanship. gr8 pics. not bad for a barman

matty

beerdoc · Post by **beerdoc** » Sat May 19, 2007 8:18 am

Tonz Magonz · Post by **Tonz Magonz** » Sat May 19, 2007 1:48 pm

Hey Doc,
Are you sure you havent spilt some rust- maker on the Rhino..?? Never seen so many rust spots in so many different places...Keep up the good work fella..Lucky you have such a ripper stripper. Hopefully see you at the coffee morning in June. Cheers Tonz

Shaven · Post by **Shaven** » Sat May 19, 2007 8:24 pm

tonz...
he loves it... cuts little holes all over the place then fixes them...

frenzix · Post by **frenzix** » Sun May 20, 2007 5:45 am

nice, im interested in the type3 engine hole... . did you have to weld in some extra support underneath?

67 panel RHINO A must for sleeping in a Panel

docs resto