Kuch's 1956 11 Window Kombi Project [16-09-08]
Moderators: warb, Rawdyn, Leroy, byronbus, Tonz Magonz, dmb
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Kuch's 1956 11 Window Kombi Project [16-09-08]
Here it is!
Been in the garage for a while, been a bit busy lately, now its time to start work, saturday will be goin for it.
Got this bus from VIC a few months ago, started workin on it and then didnt have the time, now its time to start again.
Its fairly original, 1956 11 window, little rust. The main thing to do is replace the drivers side panels due to a (i guess) 1980's panel beating job of welding and bogging an inch of bog over the top...
Seems to have had a hit towards the rear/half side end, however is still fairly straight. Not as bad as you think!
I plan on keeping it fairly original, apart from convert to IRS, Rims, dropped, original engine, etc.
This weekend will be cutting out all rust and panel work to see what i need.
Also have the brown bus (as pictured) as spare parts and panels.
Heres a few pics, but plenty more to come.
Thanks,
Kuch
Been in the garage for a while, been a bit busy lately, now its time to start work, saturday will be goin for it.
Got this bus from VIC a few months ago, started workin on it and then didnt have the time, now its time to start again.
Its fairly original, 1956 11 window, little rust. The main thing to do is replace the drivers side panels due to a (i guess) 1980's panel beating job of welding and bogging an inch of bog over the top...
Seems to have had a hit towards the rear/half side end, however is still fairly straight. Not as bad as you think!
I plan on keeping it fairly original, apart from convert to IRS, Rims, dropped, original engine, etc.
This weekend will be cutting out all rust and panel work to see what i need.
Also have the brown bus (as pictured) as spare parts and panels.
Heres a few pics, but plenty more to come.
Thanks,
Kuch
Last edited by Kuchster on Tue Sep 16, 2008 7:42 pm, edited 2 times in total.
- warb
- Mod
- Posts: 7511
- Joined: Mon May 16, 2005 5:15 pm
- Location: Penrith, Nsw, Australia
- Contact:
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Today (Sunday)
Made some modified beam holders! To sit the beam on the car stands. Dont want to use the jack points as there wont be much strength left on them with all the panels cut off. Want to get it on stands in a good position to leave the kombi up while we do the panel work.
Pressure washed it off underneath also, found some more suprises, always great isn't it... Bit chunky under there!
Kuch
Made some modified beam holders! To sit the beam on the car stands. Dont want to use the jack points as there wont be much strength left on them with all the panels cut off. Want to get it on stands in a good position to leave the kombi up while we do the panel work.
Pressure washed it off underneath also, found some more suprises, always great isn't it... Bit chunky under there!
Kuch
- Leroy
- DSKer
- Posts: 2544
- Joined: Thu Jul 05, 2007 11:58 pm
- Location: Brisbane (bayside)
- coupons
- DSKer
- Posts: 322
- Joined: Fri Nov 23, 2007 7:23 pm
- Location: north west Sydney
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Mate, you are right on that one, nearly didnt get any sleep last night, would have chucked an all nighter with the grinder, but dunno how the neighbours would feel about that!
Kuch
Kuch
Kuch's Laser Cut Products
http://www.kuch.com.au/laser
http://www.kuch.com.au/laser
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Some more work today, have to work tomorrow so will continue next weekend.
Oxying out all the spot welds, easier than drilling and so on..
Oxying off the inner sill as rusted as well and being replaced (check parts for sale for inner sill details and availability to buy)
As you cut more, you find more, so then you cut more, and have to replace more and more!
Inner sill removed
Panelbeating the floor
New sections - needs more work
Inner sill ready to go on, but will be removing jack points again and a bit more work on the outriggers
Kuch
Oxying out all the spot welds, easier than drilling and so on..
Oxying off the inner sill as rusted as well and being replaced (check parts for sale for inner sill details and availability to buy)
As you cut more, you find more, so then you cut more, and have to replace more and more!
Inner sill removed
Panelbeating the floor
New sections - needs more work
Inner sill ready to go on, but will be removing jack points again and a bit more work on the outriggers
Kuch
Last edited by Kuchster on Sun Mar 09, 2008 8:05 pm, edited 1 time in total.
- Rat214
- DSKer
- Posts: 234
- Joined: Fri Jun 01, 2007 1:48 pm
- Location: East Warburton, Victoria
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Today (Saturday)
Off come the outriggers and jack points, will replace the lot and not putting jack points back on.
Rear, what it looks like before, and replacing all top hat sections right around.
Top hat repair section welded in place.
Outrigger being mounted and top hat already in place on front.
Rear outrigger and top hat tacked in place.
Front outrigger and top hat tacked in place.
Inner sill tacked in place
Mmm rusty
Dog leg replacement panel
Can do anything with an oxy he says..
Finished
Inner dog leg all tacked in place
And more happening tomorrow.
Kuch
Off come the outriggers and jack points, will replace the lot and not putting jack points back on.
Rear, what it looks like before, and replacing all top hat sections right around.
Top hat repair section welded in place.
Outrigger being mounted and top hat already in place on front.
Rear outrigger and top hat tacked in place.
Front outrigger and top hat tacked in place.
Inner sill tacked in place
Mmm rusty
Dog leg replacement panel
Can do anything with an oxy he says..
Finished
Inner dog leg all tacked in place
And more happening tomorrow.
Kuch
- Dasdubber
- DSKer
- Posts: 1847
- Joined: Thu Dec 01, 2005 10:18 pm
- Location: Gold Coast
- Karmann1
- DSKer
- Posts: 216
- Joined: Tue Aug 07, 2007 9:36 pm
- Location: Mildura
- beerdoc
- DSKer
- Posts: 1270
- Joined: Mon May 23, 2005 7:11 pm
- Location: Geelong Vic
- Kuchster
- DSKer
- Posts: 495
- Joined: Sun Dec 02, 2007 10:12 pm
- Location: Sydney West
Sunday Today, and we are gettin further
Preparing the brown side panel, have to oxy out all the spot welds, looks like they put a few hey.. not as many in the blue kombi though.
Preparing some more
Just checking to see how it lines up
Once again, can do anything with an oxy!
Tacked in place
In position and all tacked up
Mm lookin sexy
Kuch
Preparing the brown side panel, have to oxy out all the spot welds, looks like they put a few hey.. not as many in the blue kombi though.
Preparing some more
Just checking to see how it lines up
Once again, can do anything with an oxy!
Tacked in place
In position and all tacked up
Mm lookin sexy
Kuch